Several have asked how I created the recent
Quilt of Valor
with the
Navy Military Seal/Emblem panel without using a specific pattern.
 |
| A work in progress |
I tweaked
various quilts seen on Pinterest to fit my mental design. After pondering for several weeks how to explain my crazy method ~
because math hurts my brain ~ I will attempt the explanation! Please feel free
to ask a question, or to contact me, if something isn’t clear.
Let me begin with the caveat that each Military panel square
may
will measure differently. There are differences between the branches of
service. I’ve done the
Marine and the
Army, and they both differ from the
other, and now the Navy also has its own dimensions!
First, measure the “pretty” part of the panel you’re working
with to get an overall size. (Write down the measurements somewhere for
reference later.) You’ll notice it’s probably not square! However, once it’s
all done no one will know but you!
(I usually “burn 10” when measuring something, then subtract
10. It’s just something I learned from my husband when doing construction!)
 |
| "Burning 10" |
It’s difficult to see the slight (but important) difference
on the vertical measurement! Bottom line, it is wider than taller.
 |
| "Burning Ten" |
The largest side is what you need to work with in determining the size
of blocks needed.
*How to square up/equal the panel will come later – after making
the immediate surrounding blocks!
Remember I “burn” 10 inches. You’ll see in the picture above ~ from
narrow red to narrow red across (of the original panel) ~ the sewn panel is 16.5”
wide. So, the two blocks on each of the four panel sides must be AT LEAST –
finished – 8.25” – and a bit more is a good thing!
With that in my head, because so far, my brain isn’t
hurting, I knew the blocks had to be at least 8.25 inches square (finished!)
and 8.5” (finished!) would be fabulous.
I saw this “sold” quilt on
Ebay
that I really liked. But, I’d never tried braids before.
However, I thought the “burst” effect radiating from the
center panel in this Quilt of Valor would be stunning. After searching Pinterest I believe Moda provided the best instructions in creating the braids. In their
pdf document, you’ll find
the basics:
but I quickly realized their 2 ½ x 2 ½ inch beginning square wouldn’t
be big enough, and that’s not what the Ebay quilt had in it’s beginning square.
Knowing I needed at least an 8.25 (finished) block, I guesstimated
the beginning square should be close to half the block size - a 4” square
(finished). That’s what it looks like in the picture anyway, just a tad shy of
half.
Once that was settled, I went back and followed Moda’s
instructions for the braiding. Again, following the picture found on Ebay, three
braids per side of burst – total 6 different colors used per block.
Uh Oh.
I’ve got a corner triangle thingy to figure out…
I took a scrap of fabric (leftovers from a previous quilt
backing) and cut it into a square way bigger (eye-balled) than needed. I cut
that square into two triangles. I baste-stitched the triangles on each side of
the braid, pressed as usual, then squared up the block to be at least 8.50 (finished
8.25) or 9.00 (finished 8.50).
And now wait for it … this is the magical “formula” … rip
out the basting stitches, removing the
triangles from the braids, and carefully press flat as not to stretch the bias.
Measure your triangle to determine what size of square you need to make the “real”
triangles! Tah Dah!
My head still doesn’t hurt!
*After you have four pairs of “bursts” made and starched/pressed
very well/flat (one set for each side of the panel), it’s time to figure out
what to add to the panel to make it match.
This Navy panel was itty bitty wider than taller. Yet it
must be square to make the blocks work properly!
You’ll notice at the top of the panel I used a tan “border” a
touch bigger than the side “borders”. Over all, I don’t think it’s noticeable.
It is what it is.
I worked the sides first, then added the top & bottom,
cutting the strips a bit wider than what would be needed. For me, it’s easier
to trim off a little at a time, all the way around, to match the set of star
burst pairs.
Once you’ve stitched that first set of top/bottom and sides of
star bursts pairs all the way around the panel, you’ll be set to finish out the
quilt with the same blocks!
If all this is as clear as mud, please let me know!
Happy creating something without a pattern! ;)
